Chorus Component

The Chorus mixes two identical signals, with one of the signals delayed by a small, slowly modulated amount. The Chorus produces peaks and notches in the output frequency spectrum, related to one another in a linear harmonic series. Modulating the delay time causes the peaks and notches to sweep up and down the frequency spectrum. The Chorus splits the input signal, delays and filters one of the signals (wet) then mixes it with the other signal (dry) to produce the effect.

Input - Mono or Stereo audio.

Output - Mono or Stereo audio; processed, unprocessed or a mixture of both.

Controls

Control	Function	Default/Range
Master Bypass	Bypasses all of the Chorus' controls.	Unmuted / Muted
Stereo Spread (%)	Available when the I/O Configuration Property is set to Stereo In/Stereo Out. Determines the separation spread between the channels. 0% is equal amount of each channel mixed to the other, 100% is complete separation of the channels.	Default = 100 0 - 100
High-Pass Frequency (Hz)	Frequencies below this frequency are attenuated. All frequencies above this frequency are amplified based on the setting of the Wet Gain control.	Default = 7,500 Range = 10 - 20,000
Low-Pass Frequency (Hz)	Frequencies above this frequency are attenuated. All frequencies below this frequency are amplified based on the setting of the Wet Gain control.	Default = 5,000 Range = 10 - 20,000
LFO Frequency (Hz)	The frequency at which the LFO produces the waveform, or LFO Shape. The LFO Frequency controls the speed, at which the Delay is modulated.	Default = 3.20 Range = 0.01 - 120
LFO Shape	You can select one of 4 different waveforms.	Default = 1 Range = Sine, Saw Up, Saw Down, Triangle
LFO Left /Right Phase (%)	Available when the I/O Configuration Property is set to Mono In/ Stereo Out, or Stereo In/Stereo Out. In either of the Stereo modes, the LFO produces two synchronized waveforms, one for each channel. The LFO Spread determines the phase shift between these two LFO waveforms. 0% is in phase, 100% is 180° out of phase.	Default = 10 Range = 0 - 100
Delay (ms)	The amount of time the wet signal is delayed from the dry signal. The center delay of the modulation, or Depth - the delay time is modulated around this time amount. Sets the maximum modulation Depth. If you set the Depth to it's maximum (100 ms) then the Delay amount will control the Depth amount.	Default = 7.0 Range = 0.083 - 500
Depth (ms)	The amount or Depth of the delay modulation. The Depth control is limited by the Delay control setting.	Default = 1.0 Range = 0.100 - 3.50
Wet Solo	When engaged, allows you to listen to the wet signal by itself.	Normal / Solo
Wet Gain (dB)	Controls the gain of the wet output.	Default = 0 Range = -100 - 20
Dry/Wet Mix (%)	The percentage of wet to dry signal sent to the output. 0% is all dry signal, and no wet. 100% is all wet, and no dry.	Default = 50.0 Range = 0 - 100

Control

Function

Default/Range

Master Bypass

Bypasses all of the Chorus' controls.

Unmuted / Muted

Stereo Spread

(%)

Available when the I/O Configuration Property is set to Stereo In/Stereo Out.

Determines the separation spread between the channels. 0% is equal amount of each channel mixed to the other, 100% is complete separation of the channels.

Default = 100

0 - 100

High-Pass Frequency

(Hz)

Frequencies below this frequency are attenuated. All frequencies above this frequency are amplified based on the setting of the Wet Gain control.

Default = 7,500

Range = 10 - 20,000

Low-Pass Frequency

(Hz)

Frequencies above this frequency are attenuated. All frequencies below this frequency are amplified based on the setting of the Wet Gain control.

Default = 5,000

Range = 10 - 20,000

LFO Frequency

(Hz)

The frequency at which the LFO produces the waveform, or LFO Shape. The LFO Frequency controls the speed, at which the Delay is modulated.

Default = 3.20

Range = 0.01 - 120

LFO Shape

You can select one of 4 different waveforms.

Default = 1

Range = Sine, Saw Up, Saw Down, Triangle

LFO
Left /Right Phase

(%)

Available when the I/O Configuration Property is set to Mono In/ Stereo Out, or Stereo In/Stereo Out.

In either of the Stereo modes, the LFO produces two synchronized waveforms, one for each channel. The LFO Spread determines the phase shift between these two LFO waveforms. 0% is in phase, 100% is 180° out of phase.

Default = 10

Range = 0 - 100

Delay

(ms)

The amount of time the wet signal is delayed from the dry signal.
The center delay of the modulation, or Depth - the delay time is modulated around this time amount.
Sets the maximum modulation Depth. If you set the Depth to it's maximum (100 ms) then the Delay amount will control the Depth amount.

Default = 7.0

Range = 0.083 - 500

Depth

(ms)

The amount or Depth of the delay modulation. The Depth control is limited by the Delay control setting.

Default = 1.0

Range = 0.100 - 3.50

Wet Solo

When engaged, allows you to listen to the wet signal by itself.

Normal / Solo

Wet Gain

(dB)

Controls the gain of the wet output.

Default = 0

Range = -100 - 20

Dry/Wet Mix

(%)

The percentage of wet to dry signal sent to the output. 0% is all dry signal, and no wet. 100% is all wet, and no dry.

Default = 50.0

Range = 0 - 100

Properties

Property	Function	Choices
I/O configuration	Sets the configuration of inputs and outputs for the Chorus component.	Mono In / Mono Out Mono In / Stereo Out Stereo In / Stereo Out
Max Delay (Seconds)	Sets the maximum delay allowed for the Delay knob in the component's control panel.	0.001 to 1.0

Property

Function

Choices

I/O configuration

Sets the configuration of inputs and outputs for the Chorus component.

Mono In / Mono Out

Mono In / Stereo Out

Stereo In / Stereo Out

Max Delay

(Seconds)

Sets the maximum delay allowed for the Delay knob in the component's control panel.

0.001 to 1.0

Control Pins

The available Control Pins depend on settings in Properties.

Pin Name	Value	String	Position	Pins Available
Delay	0.000 - 0.50	.083ms - 50ms	0.00 - 1.00	Input / Output
Depth	0.000 - 1.00	0.100 - 3.50ms	0.00 - 1.00	Input / Output
Dry/Wet Mix	0.00 - 100	—	0.00 - 1.00	Input / Output
High-Pass Frequency	10.0 - 20,000	10Hz - 20kHz	0.00 - 1.00	Input / Output
LFO Frequency	0.350 - 5.0	0.35Hz - 5Hz	0.00 - 1.00	Input / Output
Stereo Spread	0.00 - 100	—	0.00 - 1.00	Input / Output
LFO Waveform	1 - 4	Sine Saw Up Saw Down Triangle	0 .333 .666 1.00	Input / Output
Low-Pass Frequency	20.0 - 20,000	20Hz - 20kHz	0.00 - 1.00	Input / Output
Master Bypass	0 1	no bypassed	0 1	Input / Output
Output Gain	-60 to 20	-60 dB to 20 dB	0.000 to 1.00	Input / Output
Stereo Spread	0.00 - 100	—	0.00 - 1.00	Input / Output
Wet Solo	0 1.0	normal solo	0.00 1.00	Input / Output

Pin Name

Value

String

Position

Pins Available

Delay

0.000 - 0.50

.083ms - 50ms

0.00 - 1.00

Input / Output

Depth

0.000 - 1.00

0.100 - 3.50ms

0.00 - 1.00

Input / Output

Dry/Wet Mix

0.00 - 100

—

0.00 - 1.00

Input / Output

High-Pass Frequency

10.0 - 20,000

10Hz - 20kHz

0.00 - 1.00

Input / Output

LFO Frequency

0.350 - 5.0

0.35Hz - 5Hz

0.00 - 1.00

Input / Output

Stereo Spread

0.00 - 100

—

0.00 - 1.00

Input / Output

LFO Waveform

1 - 4

Sine

Saw Up

Saw Down

Triangle

.333

.666

1.00

Input / Output

Low-Pass Frequency

20.0 - 20,000

20Hz - 20kHz

0.00 - 1.00

Input / Output

Master Bypass

bypassed

Input / Output

Output Gain

-60 to 20

-60 dB to 20 dB

0.000 to 1.00

Input / Output

Stereo Spread

0.00 - 100

—

0.00 - 1.00

Input / Output

Wet Solo

1.0

normal

solo

0.00

1.00

Input / Output

© 2009 - 2016 QSC, LLC. All rights reserved. QSC and the QSC logo are trademarks of QSC, LLC in the U.S. Patent and Trademark office and other countries. All other trademarks are the property of their respective owners.

http://patents.qsc.com.